VLA

VisualLink is a RAD toolkit for the creation of SCADA / HMI (Supervisory Control And Data Acquisition / Human Machine Interface) applications supporting a wide range of instrument protocols. The Mantracourt range of intelligent instrumentation is supported along with a range of common 3rd party instruments. Generic drivers enable you to connect to unsupported instruments. An evaluation version of this software with full functionality is available on request. Use VisualLink to create Virtual Instrumentation, Automated Test Equipment and Batching Systems to name but a few application areas. VisualLink is event-driven and these events are generated by the different objects you place on the page. Write script code for powerful control over your system. The programming language is VBScript (a subset […]

Read More...

PP1-SP1

A high capacity battery pack with solar and mains charging providing long term 12 Volt power for field applications, specifically T24-RDC Remote Data Collection Device. The Power Pack & Solar Panel provides dependable off-grid power generation to support a variety of Mantracourt products. Packaged in an IP65 / NEMA 4 sealed case with rugged waterproof connectors the PP1 has two sources of charge for the internal battery with both solar and mains power input charging. The case also features stainless steel padlock protectors for easily securing your supply on site. The PP1 has a single 12 Volt fuse protected output. The mating connector comes pre-fitted with 5 metres of cable and bare end connections. The solar panel features hail-proof tempered […]

Read More...

T24-ANT

The Wireless Sensor Antennas T24 options of T24-ANTA, T24-ANTB and T24-ANTC are three antenna options which can be integrated with any of the T24 Modules.  They are factory fitted with UFL antenna connectors such as the external antenna options of the acquisition modules (T24-SAe, T24-IAe, T24-VAe). Options also exist for antennas to be fitted to other modules within the T24 range – please contact us for more information. The T24-ANTA Wireless Sensor Antenna is a PCB antenna designed to be fitted inside a plastic enclosure with a cable length of 100 mm (4”) UFL-UFL. The T24-ANTB is a whip antenna with a fixed 90 degree elbow designed for mounting externally with a cable length of 100 mm plus a UFL connector. We […]

Read More...

T24-AR

The wireless range repeater or extender T24-AR is a repeater enabling the T24 telemetry system modules to span around obstacles, increase range and coverage by re-transmitting received messages. The T24-AR will repeat the data once which can then double the wireless range and improve communication around obstacles. The data sent by transmitter modules can be utilised by multiple receivers such as displays, , analogue outputs, relay modules and computer interfaces. Receivers support common industrial power supplies and are available in with internal antennas optimised to give outstanding coverage. The T24-AR has a rugged IP67 rated housing enclosure for harsh environments.  There are 4 mounting holes on the back of the ABS case for wall mounting if required. It can be powered […]

Read More...

T24-BC1

This Lithium Battery Telemetry Charger module T24-BC1 can be used with the range of T24 wireless acquisition modules.  It is a compact battery charger and power supply. From a 5 Volt supply the module produces a regulated 3.3V for the acquisition module and can also charge a suitable Li-ion Battery. The Lithium Battery Telemetry Charger comes pre-configured to give a charging current of 466mA suitable for VARTA LIP653450. In addition, it also supports additional batteries providing a charge current of 133mA via the removal of the leaded resistor (non surface mount). Supply Voltage 4.1 to 6 Volts Regulated Voltage Output 3.3 V Battery Positive Connection 3.7 V Maximum Cable Length 150mm Dormant PCB Current 1.7μA * 07/02 gauge wire attached […]

Read More...

T24-AO1

The analogue output wireless receiver T24-AO1 converts data from a T24 wireless transmitter module into an analogue output and provides 0-10 Volts, ±10 Volts, 0-5 Volts, ±5 Volts, 0-20 mA and 4-20 mA (All current outputs both sink and source). Data from any of the T24 range of transmitters can be used. Two versions of the analogue output wireless receiver are available: T24-AO1 – IP50 T24-AO1i – IP67 Industrial Version Both analogue output wireless receivers offer the same output functionality, but the T24-AO1 is designed for desktop applications and is IP50 rated.  The T24-AO1i is ideal for industrial environments thanks to its IP67 protection rating. Multiple receivers can deal with the data sent by transmitter modules such as displays, , analogue outputs, relay […]

Read More...

T24LOG24

This software release for Windows allows up to 24 T24 modules (T24-SA, T24-VA , T24- TA, T24-RA, T24-PA or T24-IA) to be viewed and logged to a CSV file. You can configure the number of channels, communications settings, main title and the channel descriptions and these configurations can be saved and loaded at any time.

Read More...

T24-DPV

A simple viewing and logging program allowing users to view and log data from a single T24 radio telemetry acquisition module. The module to be interrogated is chosen from a list of available T24 devices detected on the radio channel selected. Select the radio channel required and choose a device to view from the list of detected devices. Once viewed the data can be logged to a CSV file Select a required device View the value on a simulated LCD display Log the data to a CSV file NOTE: Only works with the USB base station T24-BSU The program also performs sleeping and waking allowing battery life to be conserved when not in use. The log file created is a […]

Read More...

T24-TK

The T24-TK has been designed to ease and simplify the configuration and calibration of all modules in the T24 product range. The software recognises the connected ( or ‘paired’) module and presents a set of specifically tailored pages in a clear and user-friendly manner. In most cases a T24 system will require initial configuration using the toolkit after which the system will operate autonomously. The toolkit would only be required again if the configuration required changing. The data viewer and logging functions can be used on an existing, installed system without interrupting its operation.

Read More...

T24-VA

The T24-VA transmitter module connects to 0-10 V conditioned sensors such as pressure, %RH, inclinometer, accelerometer, depth, vibration, temperature and flow. It forms part of the T24 modular telemetry system. The data transmitted by the T24-VA can be received by multiple T24 receivers that include displays, handheld readers, analogue outputs, relay modules and computer interfaces. T24 transmitters have been designed for battery operation and support an ultra low-power sleep mode whilst offering class leading wireless coverage and range. Configurable transmission rates from once per day to 200 per second cope with a wide range of measurement and monitoring applications. A choice of enclosures enabling battery connection, field connectivity and environmental sealing up to IP67 ensure these modules provide a flexible […]

Read More...